1
Булат
no recommendations
no complaints
Project title: Implementation of construction kits CM, KZH stage RD
Type of cooperation: Periodic employment
Section: Engineering. Drawings
Prepayment: prepayment is possible
Payment methods: Cash, Bank transfer
Acceptance of requests: from 2024-02-09 until 2024-02-19
Type of cooperation: Periodic employment
Section: Engineering. Drawings
Prepayment: prepayment is possible
Payment methods: Cash, Bank transfer
Acceptance of requests: from 2024-02-09 until 2024-02-19
Project description:
Offering remote work. It is required to perform construction kits CM, CR stage RD.
Object: object OPO (technological unit), grid 2x8x9000 meters, main height +15. Partially to +55.00. The slats are reinforced concrete, the rest metal. In the block equipment, pipes, cable tracks, etc.
The required amount of working documentation:
- development of a set of CM, CM with confirmation of calculations in SCAD software or analogues
3D model development in Tekla Structures
Briefly the main one above.
Based on:
- initial data from the customer - these are the tasks of the subcontractors for the development of CM, KZH, the PD stage, 3D model, etc.
Imagine:
Remote desktop with software (if necessary)
- in rubles. Up to 20% advance, additionally after the closing of the stages and until the final.
- on the basis of the results, further cooperation
- the format of the work is supposed to be removed with the conclusion of an urgent contract. Based on the interim results (negative scenario), a face-to-face visit is necessary with the development of measures to eliminate comments. Extreme measure, quick change of performer. - strict compliance with the terms of the contract between the contractor and the customer. Both ways, of course.
-
We demand a high level of personal responsibility.
It is planned to have a serious amount of work in a short time of 1-1.5 months.
Priorities for descending:
1. Engineer KM, KZH with knowledge of Tekla, ready for the period of work to devote a serious amount of time at the start.
2. Experienced Calculator-Builder (the calculation of the frame m / k, gba, etc.) with design according to the requirements of the customer. SCAD/IDEA Statica/LIRA SAPR, etc.
3. Individual experienced specialists in CM, KZH
4. Ability to work and have experience in lifting 2D drawings in Tekla Structures.
Attention:
We ask you to take seriously the assessment of your strength, the necessary experience, the time to perform this task.
Offering remote work. It is required to perform construction kits CM, CR stage RD.
Object: object OPO (technological unit), grid 2x8x9000 meters, main height +15. Partially to +55.00. The slats are reinforced concrete, the rest metal. In the block equipment, pipes, cable tracks, etc.
The required amount of working documentation:
- development of a set of CM, CM with confirmation of calculations in SCAD software or analogues
3D model development in Tekla Structures
Briefly the main one above.
Based on:
- initial data from the customer - these are the tasks of the subcontractors for the development of CM, KZH, the PD stage, 3D model, etc.
Imagine:
Remote desktop with software (if necessary)
- in rubles. Up to 20% advance, additionally after the closing of the stages and until the final.
- on the basis of the results, further cooperation
- the format of the work is supposed to be removed with the conclusion of an urgent contract. Based on the interim results (negative scenario), a face-to-face visit is necessary with the development of measures to eliminate comments. Extreme measure, quick change of performer. - strict compliance with the terms of the contract between the contractor and the customer. Both ways, of course.
-
We demand a high level of personal responsibility.
It is planned to have a serious amount of work in a short time of 1-1.5 months.
Priorities for descending:
1. Engineer KM, KZH with knowledge of Tekla, ready for the period of work to devote a serious amount of time at the start.
2. Experienced Calculator-Builder (the calculation of the frame m / k, gba, etc.) with design according to the requirements of the customer. SCAD/IDEA Statica/LIRA SAPR, etc.
3. Individual experienced specialists in CM, KZH
4. Ability to work and have experience in lifting 2D drawings in Tekla Structures.
Attention:
We ask you to take seriously the assessment of your strength, the necessary experience, the time to perform this task.
