1
Алексей
no recommendations
no complaints
Project title: Create a diagram and write a sketch for the arduino project
Type of cooperation: One-time project
Section: Software development
Prepayment: without prepayment
Payment methods: Cash, Electronic money
Acceptance of requests: from 2022-02-20 until 2022-02-27
Type of cooperation: One-time project
Section: Software development
Prepayment: without prepayment
Payment methods: Cash, Electronic money
Acceptance of requests: from 2022-02-20 until 2022-02-27
Project description:
Offering extra earnings. It is necessary to create a connection scheme and a sketch of the device based on the arduino with an IC sensor, a gearbox motor, a speaker with an amplifier and a GRB tape.
The mechanics are:
- switch on the device with a button,
- the speaker emits the sound of the switching on
- GB tape (spotlight) blinks white, the gearbox motor begins to work.
Next:
- When an IC pulse hits this device from our stand (for ease of understanding, let us assume that we press the remote buttons from the TV) into the IC sensor on the board, there are only four commands:
- when the signal #1 (one button remote) is hit, the RGB tape lights up in red and a short sound signal is emitted from the speaker;
- when the signal #2 hits the tape lights up in blue and the same sound signal is emitted from the speaker
- when the signal #3 RGB is hit, the tape lights up in green and the same sound signal is emitted from the speaker
- when the signal #4 RGB is hit, the tape lights up in yellow and the same audible signal is emitted from the speaker.
It is necessary to make the device work for a given time (with the possibility of changing the interval using a button) and after the specified time interval, an audible signal is emitted, the gearbox motor stops and the tape flashes a color that burns longer on the board (ie. Let’s assume the interval of a given 5 min – the sensor was pressed for example red signal / blue signal / red / blue, etc., and of these 5 min tape, for example, burned in red for a total of 3 min, and blue 2 min = means tape after 5 min blinks red. Or for example, the tape burned longer in blue than red, then blinks in blue.
What time frame and how much will it cost?
Offering extra earnings. It is necessary to create a connection scheme and a sketch of the device based on the arduino with an IC sensor, a gearbox motor, a speaker with an amplifier and a GRB tape.
The mechanics are:
- switch on the device with a button,
- the speaker emits the sound of the switching on
- GB tape (spotlight) blinks white, the gearbox motor begins to work.
Next:
- When an IC pulse hits this device from our stand (for ease of understanding, let us assume that we press the remote buttons from the TV) into the IC sensor on the board, there are only four commands:
- when the signal #1 (one button remote) is hit, the RGB tape lights up in red and a short sound signal is emitted from the speaker;
- when the signal #2 hits the tape lights up in blue and the same sound signal is emitted from the speaker
- when the signal #3 RGB is hit, the tape lights up in green and the same sound signal is emitted from the speaker
- when the signal #4 RGB is hit, the tape lights up in yellow and the same audible signal is emitted from the speaker.
It is necessary to make the device work for a given time (with the possibility of changing the interval using a button) and after the specified time interval, an audible signal is emitted, the gearbox motor stops and the tape flashes a color that burns longer on the board (ie. Let’s assume the interval of a given 5 min – the sensor was pressed for example red signal / blue signal / red / blue, etc., and of these 5 min tape, for example, burned in red for a total of 3 min, and blue 2 min = means tape after 5 min blinks red. Or for example, the tape burned longer in blue than red, then blinks in blue.
What time frame and how much will it cost?
